On the underside of this unit controls are accessible to set the:
All the versions of this transmitter will operate with a power supply of 12-15V DC (0.6 amp) or worldwide mains 90 to 260V AC.
Our 1W ERP System package includes this transmitter with a single dipole antenna or our 2W ERP system with a stacked dipole antenna. Both give a full system that complies with the regulations of the European Union and most other countries in the world.
MPX. - This is the low cost version, but is not intended for the novice or beginners. The audio input is raw MPX without any audio limiting or stereo coder circuitry, this must be provided externally in accordance with the recommendations of http://www.aareff.com/ETR132.pdf
Click here for user manual
Stereo Version. - This is identical to Mono/MPX version but with a stereo coder built in. RDS cannot be used with this. Again it does not include audio limiting, so it's not recommended for the novice or beginner. External limiting need to comply with the recommendations of http://www.aareff.com/ETR132.pdf
Mono and Audio Processing. - This particular version is in mono only, so it not suitable for music stations. This would be used for talk stations, church broadcast etc. It includes audio processing circuitry and suitable limiting to keep the transmitter in compliance with the maximum bandwidth permitted by the international regulations and is suitable for the novice or beginner.
Stereo and Audio Processing. - Most small radio stations and beginners will use this version, this is because it includes audio processing circuitry and suitable limiting to keep the transmitter in compliance with the maximum bandwidth permitted by the international regulations. There is also access to the MPX in and out on the back panel which allows all known RDS units to be connected.
Click here for user manual
This FM transmitter system along with all our other products comes with a limited 2 year warranty (see warranty conditions)
All these models comply with European standards ETS 300384 for R&TTE, EN 301 489-11 for EMC and (LVD) 2006/95/EC for safety, the relevant FCC sections of US 47 CFR Part 73 for verification and ITU-R BS.450-3 (11/01) FM Broadcasting at VHF.
|Audio Input Sensitivity||+4 dBu for +/- 75 KHz dev.|
|Freq Stability||+/- 1 KHz max. typ. +/-300 Hz|
|Deviation Sensitivity Stability||+/-2 % max|
|Freq Fine Adj||> +/- 1000 Hz|
|Pre-emphasis||(50 uS/ 75 uS/ None) Selectable|
|Audio Input Connector||Phono/ RCA type unbalanced sockets|
|Power Output||Adj. 0.01 to 1 Watt into 50 ohms|
|Freq Range||87.5 to 108 MHz in 100 KHz steps|
|Spurious Emissions||Less than -66 dB ref to carrier|
|Harmonic Emissions||Less than -66 dB ref to carrier|
|Out of Lock RF Muting||Less than -66 dB ref to carrier|
|Residual AM||Less than 0.5 %|
|Synchronous AM||Less than 0.5 %|
|RF Ruggedness||Any VSWR phase or length of time|
|Output Connector||SO239 (or optional N type)|
|Input Connector||BNC 50 ohms|
|Operating Temp||-20 to +50 Deg C|
|Version||MPX||Stereo||Stereo and Audio Processor|
|Signal To Noise Ratio||80dB||65dB||65dB|
|Audio Distortion||0.2% THD Max||0.2% THD Max||0.2% THD Max (at MPX section)|
|Stereo Pilot Tone||None||19KHz +/-0.2Hz||19KHz +/-0.2Hz|
|Model||Power Supply GE12I15|
|Input Voltage||90-264 V AC 135-370 V DC 47-63 Hz|
|Power Factor||PF 0.91/230V AC PF 0.95/115V AC at full load|
|Input Power||11W max. for 1W RF OUT with RF SWR less than 1.5|
|Working Humidity||20-90% RH non-condensing|
|Safety Standards||UL60950-1, CSA C22.2, TUV EN60950 -1, AS/NZS 60950.1, CCC GB4943 approved|
|EMC Emission||Compliance to EN55022, EN61000-3-2,3, FCC part15, GB9254, GB17625.1|
|EMC Immunity||Compliance to EN61000-4-2 3 4 5 6 8 11 light industry level criteria A|